Reset your Holosun EPS Carry Red Dot Sight

Occasionally, you may require to reset your Holosun EPS Carry Red Dot sight to its factory settings. This can be helpful if you've been tinkering with the adjustments or are experiencing unexpected behavior. Fortunately, resetting your Holosun is a straightforward process that can be achieved in just a few steps.

Initially ensuring your red dot sight is activated.
Find the small reinitialize button on the rear of the device.
Employ a small object to activate the reset lever for approximately three moments.
Let go the lever and your Holosun EPS Carry Red Dot sight will power cycle.
The red dot sight should now be reverted to its factory settings.

Reset Your Holosun EPS Carry Red Dot back to Defaults

In case you've tweaked your Holosun EPS Carry red dot settings and want to start fresh, resetting it to default configuration is a breeze. First, find the tiny button on the bottom of your optic. Then, press and hold it for around ten seconds until you see the red dot blink. Your Holosun EPS Carry is now reverted to its factory settings, ready for accurate shooting.

Bring Your Holosun EPS Carry Back to Life

Is your beloved Holosun EPS Carry experiencing some issues? Don't despair! A simple factory reset can often solve the problem and get your red dot sight back to its former glory. Before you begin, remember to detach the battery from your Holosun EPS Carry to prevent unintended activation during the process.

To perform a factory reset on your Holosun EPS Carry, follow these simple steps:

Press and hold the power button for approximately 5 seconds.
The display will flash, indicating that the reset is being performed.
Release the power button once the reset is complete.

Your Holosun EPS Carry should now be back to its factory settings. You can insert the battery and verify your sight's functionality. If you encounter any further difficulties, don't hesitate to reach out to their technical assistance.

Restore Factory Settings on Your Holosun EPS Carry: A Step-by-Step Guide

Resetting your Holosun EPS Carry to factory settings can be a helpful solution if you're experiencing issues with the optic or simply want to start fresh. This process erases all user configurations and returns the sight to its original state. Before proceeding, remember to note down any customizations you have made as they will be lost during this process. Follow these steps carefully to ensure a successful factory reset.

Beginning with, Energize your Holosun EPS Carry by pressing the power button.
Next, press and hold both the mode button and the up/down adjustment button simultaneously.
As you continue holding these buttons, press the power button once.
You will show a confirmation prompt indicating that the reset process is initiated.
Allow the process to finish. This may take a few moments. Once done, your Holosun EPS Carry will automatically power off.

After resetting your Holosun EPS Carry to factory settings, you will need to re-enter any desired customizations, such as brightness levels and reticule style. Refer to the user manual for detailed instructions on configuring your optic after a reset.

Reset All Settings on Your Holosun EPS Carry

To Factory reset your Holosun EPS Carry sight, you'll need to access the settings menu. This can usually be done by Turning a specific button combination. Consult your Guidebook for the exact button sequence for your model. Once in the settings menu, look for an option that says "Factory Default". Select this option and confirm the reset. Your sight will then power off and restart with all settings Restored to their default values.

Reinitialize your Holosun EPS Carry with a Factory Original Settings

If your Holosun EPS Carry is here acting up, a factory reset might be the fix. This will restore your sight to its initial settings, clearing any altered configurations you've made. To accomplish this reset, observe these straightforward steps:

First, locate the reset lever on your EPS Carry.
Then, press a small object, like a pen tip, to activate the reset lever.
During maintain the reset switch pressed, activate your EPS Carry.
You'll blink a message indicating that the reset is finished.

Once the reset is successful, your EPS Carry will be back to its factory settings.